2022 Valid 300-410 Exam Updates - 2022 Study Guide
300-410 Certification - The Ultimate Guide [Updated 2022]
What's Next After Cisco ENARSI?
Once you have passed the Cisco ENARSI 300-410 exam, assuming you have already passed the core 350-401 ENCOR test, and have been awarded the prestigious CCNP Enterprise certification, you get new prospects for professional improvement. Earning this certificate automatically earns you the right to boast about it on social media platforms such as LinkedIn to attract more and more job offers with high paying salaries. CCNP Enterprise is valid for a total of 3 years, after which recertification should be done by keeping up with educational activities offered by Cisco or completing exams. Finally, one can also opt for expert-level certifications such as CCIE Enterprise Infrastructure or CCIE Enterprise Wireless. Each of them requires applicants to only pass one extra lab exam.
NEW QUESTION 185
Refer to the exhibit. The network administrator has configured the Customer Edge router (AS 64511) to send only summarized routes toward ISP-1 (AS 100) and ISP-2 (AS 200).
router bgp 64511
network 172.16.20.0 mask 255.255.255.0
network 172.16.21.0 mask 255.255.255.0
network 172.16.22.0 mask 255.255.255.0
network 172.16.23.0 mask 255.255.255.0
aggregate-address 172.16.20.0 255.255.252.0
After this configuration. ISP-1 and ISP-2 continue to receive the specific routes and the summary route. Which configuration resolves the issue?
- A. interface E 0/0
ip bgp suppress-map BLOCK_SPECIFIC
!
interface E 0/1
ip bgp suppress-map BLOCK_SPECIFIC
!
ip prefix-list PL_BLOCK_SPECIFIC permit 172.16.20.0/22 ge 24
!
route-map BLOCK_SPECIFIC permit 10
match ip address prefix-list PL_BLOCK_SPECIFIC - B. router bgp 64511
aggregate-address 172.16.20.0 255.255.252.0 summary-only - C. ip prefix-list PL_BLOCK_SPECIFIC deny 172.16.20.0/22 ge 22
ip prefix-list PL BLOCK SPECIFIC permit 172.16.20.0/22
!
route-map BLOCK_SPECIFIC permit 10
match ip address prefix-list PL_BLOCK_SPECIFIC
!
router bgp 64511
aggregate-address 172.16.20.0 255 255.252.0 suppress-map BLOCKSPECIFIC - D. router bgp 64511
neighbor 192.168.100.1 summary-only
neighbor 192.168.200.2 summary-only
Answer: B
Explanation:
When the aggregate-address command is used within BGP routing, the aggregated address is advertised, along with the more specific routes.
The exception to this rule is through the use of the summary-only command. The "summary-only" keyword suppresses the more specific routes and announces only the summarized route.
NEW QUESTION 186
After some changes in the routing policy, it is noticed that the router in AS 45123 is being used as a transit AS router for several service provides. Which configuration ensures that the branch router in AS 45123 advertises only the local networks to all SP neighbors?
A)
B)
C)
D)
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: D
NEW QUESTION 187
Refer to the exhibit.
Which interface configuration must be configured on the HUB router to enable MVPN with mGRE mode?
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_dmvpn/configuration/15-mt/sec-conn-dmvpn-15-m
NEW QUESTION 188
Drag and drop the MPLS VPN device types from me left onto the definitions on the right.
Answer:
Explanation:
NEW QUESTION 189
Drag and drop the operations from the left onto the locations where the operations are performed on the right.
Answer:
Explanation:
Explanation
Label Switch Router 1. Reads labels and forwards the packet based on the based on the label.
2. Performs PHP
Label Edge Router: 1 Assigns labels and unlabeled packets.
2. Handles traffic between multiple VPNs
NEW QUESTION 190
Drag and drop the DHCP messages from the left onto the correct uses on the right.
Answer:
Explanation:
Explanation
DHCPACK
The server-to-client communication with configuration parameters, including committed network address.
DHCPINFORM
The client-to-server communication, asking for only local configuration parameters that the client already has externally configured as an address.
DHCPNAK
The server-to-client communication, refusing the request for configuration parameter.
DHCPDECLINE
The client-to-server communication, indicating that the network address is already in use
NEW QUESTION 191
A company is expanding business by opening 35 branches over the Internet. A network engineer must configure DMVPN at the branch routers to connect with the hub router and allow NHRP to add spoke routers securely to the multicast NHRP mappings automatically Which configuration meets this requirement at the hub router?
A)
B)
C)
D)
- A. Option C
- B. Option D
- C. Option B
- D. Option A
Answer: A
NEW QUESTION 192
An engineer configured a leak-map command to summarize EIGRP routes and advertise specifically loopback
0 with an IP of 10.1.1.1.255.255.255.252 along with the summary route. After finishing configuration, the customer complained not receiving summary route with specific loopback address. Which two configurations will fix it? (Choose two.)
- A. Configure route-map Leak-Route permit 20.
- B. Configure route-map Leak-Route permit 10 and match access-list 1.
- C. Configure access-list 1 and match under route-map Leak-Route.
- D. Configure access-list 1 permit 10.1.1.0.0.0.0.3.
- E. Configure access-list 1 permit 10.1.1.1.0.0.0.252.
Answer: B,D
Explanation:
Explanation
When you configure an EIGRP summary route, all networks that fall within the range of your summary are suppressed and no longer advertised on the interface. Only the summary route is advertised. But if we want to advertise a network that has been suppressed along with the summary route then we can use leak-map feature. The below commands will fix the configuration in this question:
R1(config)#access-list 1 permit 10.1.1.0 0.0.0.3
R1(config)#route-map Leak-Route permit 10 // this command will also remove the "route_map Leak-Route deny 10" command.
R1(config-route-map)#match ip address 1
NEW QUESTION 193
Refer to the exhibit.
An engineer is trying to connect to R1 via Telnet with no success. Which configuration resolves the issue?
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: D
NEW QUESTION 194
Refer to the exhibit.
ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console. Which command is missing from the IP SLA configuration?
- A. Start-time now
- B. Start-time 0
- C. Start-time 00:00
- D. Start-time immediately
Answer: A
NEW QUESTION 195
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.
Answer:
Explanation:
NEW QUESTION 196
Refer to the exhibit.
Network operations cannot read or write any configuration on the device with this configuration from the operations subnet. Which two configurations fix the issue? (Choose two.)
- A. Configure SNMP rw permission in addition to community ciscotest 1.
- B. Configure SNMP rw permission in addition to version 1.
- C. Modify access list 1 and allow SNMP in the access list.
- D. Modify access list 1 and allow operations subnet in the access list.
- E. Configure SNMP rw permission in addition to community ciscotest.
Answer: D,E
NEW QUESTION 197
Refer to the exhibit.
Which configuration denies Telnet traffic to router 2 from 198A:0:200C:: 1/64?
- A. Ipv6 access-list-Deny_Telnet sequence 10 deny tcp host 198A:0:200C::1/64 host 201A:0:205C::1/64 eq telnet ! int Gi0/0 Ipv6 traffic-filter Deny_Telnet in !
- B. Ipv6 access-list-Deny_Telnet sequence 10 deny tcp host 198A:0:200C::1/64 host 201A:0:205C::1/64 ! int Gi0/0 Ipv6 traffic-filter Deny_Telnet in !
- C. Ipv6 access-list-Deny_Telnet sequence 10 deny tcp host 198A:0:200C::1/64 host 201A:0:205C::1/64 eq telnet ! int Gi0/0 Ipv6 access-map Deny_Telnet in !
- D. Ipv6 access-list-Deny_Telnet sequence 10 deny tcp host 198A:0:200C::1/64 host 201A:0:205C::1/64 ! int Gi0/0 Ipv6 access-map Deny_Telnet in !
Answer: A
NEW QUESTION 198
Refer to the exhibit.
A)
B)
C)
D)
- A. Option
- B. Option
- C. Option
- D. Option
Answer: A
NEW QUESTION 199
An engineer configured the wrong default gateway for the Cisco DNA center enterprise interface during the install. Which command must the engineer run to correct the configuration?
- A. Sudo magiev-config update
- B. Sudi update config install
- C. Sudo maglev reinstall
- D. Sudo maglev install config update
Answer: D
NEW QUESTION 200
Refer to Exhibit.
A network administrator has successfully configured DMVPN topology between a hub and two spoke routers. Which two configuration commands should establish direct communications between spoke 1 and spoke 2 without going through the hub? (Choose two).
- A. At the hub router, configure ip nhrp redirect the command
- B. At the spoke routers, configure the ip nhrp shortcut command.
- C. At the hub router, configure tne Ip nhrp spoke-tunnel command
- D. At the hub router, configure the ip nhrp shortcut command.
- E. At the spoke routers, configure the ip nhrp spoke-tunnel command.
Answer: A,B
NEW QUESTION 201
Refer to the exhibit.
Refer to the exhibit The engineer configured route redistribution in the network but soon received reports that R2 cannot access 192 168 7 0/24 and 192 168 15 0/24 subnets Which configuration resolves the issue?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: A
NEW QUESTION 202
Refer to the exhibits.
Phase-3 tunnels cannot be established between spoke-to-spoke in DMVPN. Which two commands are missing? (Choose two.)
- A. The ip nhrp map command is missing on the hub router.
- B. The ip nhrp redirect command is missing on the spoke routers.
- C. The ip nhrp shortcut command is missing on the spoke routers.
- D. The ip nhrp redirect command is missing on the hub router.
- E. The ip nhrp shortcut command is missing on the hub router.
Answer: A,D
NEW QUESTION 203
Refer to the exhibit.
An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?
- A. Change sequence 10 in the route-map command from permit to deny.
- B. Add this statement to the route map: route-map RM-OSPF-DL deny 20.
- C. Use an extended access list instead of a standard access list.
- D. Use a prefix list instead of an access list in the route map.
Answer: A
NEW QUESTION 204
A router in an EVN environment is choosing a route. Which value is given the highest selection priority?
- A. replication status of the route
- B. lexical value of the source VRF name
- C. default administrative distance of the route
- D. IGP administrative distance of the route
- E. VNET tag of the route
Answer: D
Explanation:
Explanation/Reference: https://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/layer-3-vpns-l3vpn/ whitepaper_c11-638769.html
NEW QUESTION 205
Drag and Drop the IPv6 First-Hop Security features from the left onto the definitions on the right.
Answer:
Explanation:
NEW QUESTION 206
Which three protocols or protocol combinations does Management Plane Protection (MPP) support? (Choose three.)
- A. SSH
- B. Both HTTP and HTTPS
- C. Only HTTP
- D. FTP
- E. SFTP
- F. OSPF
Answer: A,B,D
Explanation:
Currently, MPP controls only the incoming management requests for protocols, such as TFTP, Telnet, Simple Network Management Protocol (SNMP), Secure Shell (SSH), and HTTP.
Following are the management protocols that the MPP feature supports. These management protocols are also the only protocols affected when MPP is enabled.
Blocks Extensible Exchange Protocol (BEEP)
FTP
HTTP
HTTPS
SSH, v1 and v2
SNMP, all versions
Telnet
TFTP
Reference: https://www.cisco.com/c/en/us/td/docs/ios/security/configuration/guide/sec_mgmt_plane_prot.html
NEW QUESTION 207
Refer to the exhibit.
To provide reachability to network 10.1.1.0 /24 from R5, the network administrator redistributes EIGRP into OSPF on R3 but notices that R4 is now taking a ........... path through R5 to reach 10.1.1.0/24 network. Which action fixes the issue while keeping the reachability from R5 to 10.1.1.0/24 network?
- A. Apply the outbound distribution list on R5 toward R4 in OSPF.
- B. Change the administrative distance of the external EIGRP to 90.
- C. Change the administrative distance of OSPF to 200 on R5.
Answer: B
NEW QUESTION 208
Refer to the exhibit.
An administrator that is connected to the console does not see debug messages when remote users log in. Which action ensures that debug messages are displayed for remote logins?
- A. Enter the transport input ssh configuration command.
- B. Enter the aaa new-model configuration command.
- C. Enter the terminal monitor exec command.
- D. Enter the logging console debugging configuration command.
Answer: D
Explanation:
The -logging console is a default and hidden command.
NEW QUESTION 209
While working with software images, an engineer observes that Cisco DNA Center cannot upload its software image directly from the device. Why is the image not uploading?
- A. The software image for the device is in bundle mode
- B. The software image for the device is in install mode.
- C. The device has lost connectivity to Cisco DNA Center.
- D. The device must be resynced to Cisco DNA Center.
Answer: B
Explanation:
Upload Software Images for Devices in Install Mode
The Image Repository page might show a software image as being in Install Mode. When a device is in Install Mode, Cisco DNA Center is unable to upload its software image directly from the device. When a device is in install mode, you must first manually upload the software image to the Cisco DNA Center repository before marking the image as golden, as shown in the following steps.
Reference:
dna-center/1-2-10/user_guide/b_cisco_dna_center_ug_1_2_10/
b_dnac_ug_1_2_10_chapter_0100.html
NEW QUESTION 210
......
Target Audience
After looking at the knowledge and skills required for the final exam, the next step for you is to find out if you are a target audience for it. As for the Cisco 300-410, the ideal candidates for it are the following individuals:
- Network Administrators;
- System Administrators.
- System Engineers;
- Enterprise Network Engineers;
300-410 Practice Exam and Study Guides - Verified By PassTorrent: https://freepdf.passtorrent.com/300-410-latest-torrent.html